8 Jul electrical specifications of ASTM F . Ground cable assemblies shall have an ampacity greater than or equal to that of No. 2 AWG copper. ASTM Standard F was originally written with the intent of covering temporary protective grounds to be used on overhead power lines. The standard was bas. Abstract– During implementation of a maintenance program that was intended to check compliance of field grounding devices with ASTM F, field personnel.
|Published (Last):||12 November 2012|
|PDF File Size:||12.3 Mb|
|ePub File Size:||16.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
Assembly ratings assume the grade of lowest graded component see In engineering terms this is known as DC offset. In the same astm f855, the initial fault current is high because of the DC component asymmetry, but drops off quickly due to I2r loss. astm f855
Astm f855 DC offset asymmetry creates the initial high current wstm the first cycles of a short circuit. ASTM does not give any warranty express or implied or make any representation that astm f855 contents of this abstract are accurate, complete or astm f855 to date.
The elastomer or thermoplastic making up the jacket of the flexible cable shall be tested according to the specified methods. Threaded female terminal connections accept externally threaded ferrule studs.
They were placed on your computer when you launched this website. I astm f855 safety as identifying and managing hazards to prevent incidents.
The DC component asymmetry drops off quickly because of I2r losses in the circuit. The threaded ferrule astm f855 inserted through the drilled terminal.
Shrouded-type ferrules are designed to be used with ASTM-type grounding cable. Subscribe to this blog post Please fill in your email address to subscribe to updates from this post. Resistance in the protective ground increases current across the worker in a fault. Alternate testing circuits are available for laboratories that cannot achieve the above astm f855. In addition, the paragraph notes that many of these cables have been tested to the ASTM standard and have been found to meet the requirements astm f855 the standard.
Astm f855 terminal connections use a plain eye bolt inserted through a hole in the clamp.
After 25 years as a transmission distribution lineman and foreman, Jim Vaughn has devoted the last 15 years to safety and training. The clamp must carry the rated current, but it is not required astm f855 survive the exposure to the point of being reused. Astm f855 ultimate rating is the current ratings the clamp can sustain in kA at 6, 15, 30 and 60 cycles.
To meet ASTM standards, temporary personal protective grounds must use multistranded flexible cable conductor installed in a rated clamp using protective cable ferrules. Grade 1 to Grade 7 Clamps Clamp grades 1 through 7 establish minimum requirements for physical strength and electrical characteristics in withstand rating, ultimate rating and continuous current, strength yield and ultimate strength.
This standard does astm f855 purport to address all of the safety concerns, if any, associated with its use. The continuous current rating is the current the clamp must conduct without overheating to failure. All clamps require a ferrule-to-terminal connection. At present, there is no Type II specification. Astm f855 29 CFR Plain copper ferrules are usually used with bronze clamps.
Type III is usually installed using a formed T-handle and is intended as a first connection to a system neutral, pole bond, or grounded station or apparatus steel that does not require use of a hot stick. Cable Capacity The current ratings for grounding cables are higher than standard service cable ratings because of the specific application, astm f855 of cable in use and expected astm f855 of applied currents. The values in parentheses are the inch-pound units. You can change your cookie settings through astm f855 browser.
While not part of the F standard, the nine styles can be unofficially grouped into three basic terminal types: The withstand rating is the current ratings the clamp can sustain in kA at 15 and 30 cycles without atsm the clamp.
Calculating Fault Current Calculation of fault current is best accomplished through the services of an engineer astm f855 in utility systems. Ferrule Types Ferrules are categorized according to ferrule-to-clamp connection method and astm f855 either shrouded or nonshrouded. If a protective astm f855 installed in an equipotential arrangement has too much resistance, it will not protect workers.
Train the Trainer 101: ASTM F855 Grounding Equipment Specs Made Simple
Assemblies that have been subjected to these shall not be re-used. The conductor size for each grade of ferrule also corresponds to the minimum single cable size specified for astm f855 clamp of the equivalent grade rating. About Testing Grounds assembled by the employer require continuity integrity testing and inspection in order to comply with Ferrules Cable ferrules are sleeves compressed onto the cable end to protect the stranding of the cable astm f855 installed in a connecting terminal.
It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior astm f855 use. Lessons from Puerto Rico.